عمر المغربي
02-02-2009, 01:21 PM
اهم اوامر النت ستات netstat
افتح الدوس run > cmd > netstat
امر مهم لمعرفة الايبهات المتصلة بجهازك netsat -b
نفس الامر netstat -n
Displays protocol statistics and current TCP/IP network connections.
NETSTAT [-a] [-b] [-e] [-n] [-o] [-p proto] [-r] [-s] [-v] [interval]
-a Displays all connections and listening ports.
-b Displays the executable involved in creating each connection
listening port. In some cases well-known executables host
multiple independent components, and in these cases the
sequence of components involved in creating the connection
or listening port is displayed. In this case the executable
name is in [] at the bottom, on top is the component it calle
and so forth until TCP/IP was reached. Note that this option
can be time-consuming and will fail unless you have sufficien
permissions.
-e Displays Ethernet statistics. This may be combined with the -
option.
-n Displays addresses and port numbers in numerical form.
-o Displays the owning process ID associated with each connectio
-p proto Shows connections for the protocol specified by proto; proto
may be any of: TCP, UDP, TCPv6, or UDPv6. If used with the -
option to display per-protocol statistics, proto may be any o
IP, IPv6, ICMP, ICMPv6, TCP, TCPv6, UDP, or UDPv6.
-r Displays the routing table.
-s Displays per-protocol statistics. By default, statistics are
shown for IP, IPv6, ICMP, ICMPv6, TCP, TCPv6, UDP, and UDPv6;
the -p option may be used to specify a subset of the default.
-v When used in conjunction with -b, will display sequence of
components involved in creating the connection or listening
port for all executables.
interval Redisplays selected statistics, pausing interval seconds
between each display. Press CTRL+C to stop redisplaying
statistics. If omitted, netstat will print the current
configuration information once.
افتح الدوس run > cmd > netstat
امر مهم لمعرفة الايبهات المتصلة بجهازك netsat -b
نفس الامر netstat -n
Displays protocol statistics and current TCP/IP network connections.
NETSTAT [-a] [-b] [-e] [-n] [-o] [-p proto] [-r] [-s] [-v] [interval]
-a Displays all connections and listening ports.
-b Displays the executable involved in creating each connection
listening port. In some cases well-known executables host
multiple independent components, and in these cases the
sequence of components involved in creating the connection
or listening port is displayed. In this case the executable
name is in [] at the bottom, on top is the component it calle
and so forth until TCP/IP was reached. Note that this option
can be time-consuming and will fail unless you have sufficien
permissions.
-e Displays Ethernet statistics. This may be combined with the -
option.
-n Displays addresses and port numbers in numerical form.
-o Displays the owning process ID associated with each connectio
-p proto Shows connections for the protocol specified by proto; proto
may be any of: TCP, UDP, TCPv6, or UDPv6. If used with the -
option to display per-protocol statistics, proto may be any o
IP, IPv6, ICMP, ICMPv6, TCP, TCPv6, UDP, or UDPv6.
-r Displays the routing table.
-s Displays per-protocol statistics. By default, statistics are
shown for IP, IPv6, ICMP, ICMPv6, TCP, TCPv6, UDP, and UDPv6;
the -p option may be used to specify a subset of the default.
-v When used in conjunction with -b, will display sequence of
components involved in creating the connection or listening
port for all executables.
interval Redisplays selected statistics, pausing interval seconds
between each display. Press CTRL+C to stop redisplaying
statistics. If omitted, netstat will print the current
configuration information once.